D.05

Tabique de zona húmeda

Wet-area partition
133 mm
Espesor total · Revisión 01 · 2026-08
D.05 Tabique de zona húmeda SCALE 1:10
1 13 mm 2 15 mm 6 90 mm 7 5 mm 8 10 mm 3 25 mm 4 40 mm 5 25 mm 133 mm Int. Int. mojado

Las capas discontinuas van dentro de la cámara entre montantes, no se suman a ella. Navegable con las flechas del teclado; los mismos datos se publican como tabla en la tabla de capas de abajo.

Fotografías

1 / 3

Tabla de capas

D.05 · tabla de capas · total 133 mm
Capa Material Espesor λ Función
1 Pladur Gypsum board 13 mm — Internal finish to the dry side
2 Perfil Ω Cold-formed galvanised steel 15 mm — Fixing profile for the lining, with a service void
3 INSULTERM 600 en la cámara Sprayed thermal-acoustic conglomerate 25 mm 0.138 W/m·K Encapsulation
4 Lana de roca en la cámara Rock wool 40 mm 0.039 W/m·K Acoustic core ISOVER Alphatoit rigid rock wool panel, as in D.02. λD from the manufacturer's datasheet (FT_Alphatoit_ES, 14/03/2024), to EN 12667 / EN 12939.
5 INSULTERM 600 en la cámara Sprayed thermal-acoustic conglomerate 25 mm 0.138 W/m·K Encapsulation, and the face the tiling is bonded to
6 Perfil de acero C 90 Cold-formed galvanised steel 90 mm — Framing — the cavity contains layers 3, 4 and 5
7 Pegamento Cement-based tile adhesive 5 mm — Bonds the tiling direct to the sprayed face
8 Alicatado Ceramic wall tile 10 mm — Wet-area finish
Total 133 mm

Una raya indica que el documento de origen no declara ese valor; no es un cero. Las capas contenidas en la cámara van sangradas: van dentro del canto del montante, por lo que la columna no suma el total.

The most distinctive detail in the set. Tiling is bonded directly to the sprayed INSULTERM 600 face — no board, no furring, no board joints or screw heads behind the tiling. That saves 28 mm on every wet wall, which is net internal area recovered on every bathroom in a scheme. At 133 mm it is the thinnest build-up Solid System publishes.

Prestaciones calculadas

D.05 · prestaciones
Propiedad Valor Base
Transmitancia U, corregida por puentes 0.60 W/m²K EN ISO 6946, one-dimensional steady state, with a +20% bridging correction applied as an engineering estimate.
Peso propio 80 kg/m² Mass estimate from the layers and dimensions in the source document.
Equivalente tradicional 129 kg/m² Derived from the published self-weight and reduction percentage.
Reducción de peso −38% Self-weight against the traditional equivalent build-up.
Resistencia al fuego (EI) Programa de ensayos en curso — contacte con el departamento técnico A la espera del informe de ensayo de laboratorio
Aislamiento a ruido aéreo (R_A) Programa de ensayos en curso — contacte con el departamento técnico A la espera del informe de ensayo de laboratorio
Estanqueidad al agua Programa de ensayos en curso — contacte con el departamento técnicoBond strength testing to EN 1348 is in progress A la espera del informe de ensayo de laboratorio

Las transmitancias son cálculos unidimensionales en régimen estacionario según EN ISO 6946. La corrección por puentes térmicos se aplica como estimación de ingeniería: +20% en muros y +15% en elementos horizontales. El análisis numérico 2D según EN ISO 10211 está en curso; los valores se actualizarán al completarlo.

Aún no declarado

  • EIResistencia al fuego · en ensayo
  • R_AAislamiento a ruido aéreo · en ensayo
  • watertightnessEstanqueidad al agua · en ensayo

Programa de ensayos en curso — contacte con el departamento técnico

Peso frente al tradicional

Elemento Solid System Tradicional Reducción
D.05 Tabique de zona húmeda 80 kg/m² 129 kg/m² −38%

Dónde se usa

  • Bathroom and kitchen partitions
  • Tiled wall zones outside direct-spray areas

Notas de diseño

  • All plumbing on the tiled face must be set out before spraying. There is no chasing afterwards.
  • Bond strength testing to EN 1348 is in progress. For shower and direct-spray zones we currently specify a liquid-applied membrane behind the tiling.
  • 28 mm is recovered per wet wall against the traditional board-and-furring equivalent.

Descargas

DWG D.05 section drawing En preparación
PDF D.05 section drawing En preparación
CSV D.05 layer schedule